Senin, 29 Februari 2016

Boat Plans Building


Im in the process of gluing the forward seat into place. This will seal the forward water-tight compartment. I have epoxy-sealed the compartment, now I just need to glue the seat down. In a final fitting session, I cut open the hole for the mast and the inspection port. However, I noticed that I needed to push down on the starboard side in order to make contact with the seat cleat. I thought I had everything pretty level but apparently not. Its not much, but to be sure I took pictures from inside the compartment with the seat in place, using the automatic timer on my computer. These were taken before I epoxy sealed the ply.

The bow, notice the faint shadow smudge on the starboard side:


More pronounced in the aft section of the tank:


Nice fit on the port side:


Anyway, neat idea to see what was going on in there. Its not perfect, but close enough. I also slightly angled the seat cleats up from the BHs to the stem in order to facilitate draining so water didnt pool up front, so that may have skewed some things a small amount.

No glue yet, just still fitting and getting ready.

Do you find information about Boat Plans Building are you looking for? If not, below may help you find more information about the Boat Plans Building. Thank you for visiting, have a great day.
Read More..

Boat Plans Bolger


Ok!

I continue to slowly progress on the boat. I am really stymied by the fact that its been all of 0 deg. F (-18 C) here at the house for quite a bit now. The garage has been holding temperature at just under freezing. Im not interested in doing major epoxy sealing work in these condititions because: a) its cold, b) the epoxy thickens and is difficult to spread.

However, I can do small spot gluing jobs. For instance, I installed the mast step and partner yesterday:



My Step was placed in first (obviously) as a whole piece, as in the 6mm ply backing was already glued in position. The fit was relatively tight, but not perfect because my BHs are not exactly perfectly parallel along the bottom. Im talking a few mms here, but still. Anyway, when you drop something into a tight spot to be glued, pay attention as to how youre going to place it in and glue those places accordingly. To clarify: Dont put the glue on the location that is going to get scraped by the incoming piece, put it where it will be squeezed in so the glue remains.

The partner went in nice and simple, except I dropped it on my heater fan. My partner deviates from the plans as in it is two pieces, with the bottom piece extending underneath the seat cleat on BH2. This is for stability issues, I could twist the top of the BH with my hand. This partner makes it very burly.

Notice my heater and my brick compression system. Its a $12 heater I bought at Lowes. With a plastic sheet, temps went up quick.

Next up I screwed the gunwales into place. I didnt want to necessarily do it, but its almost essential.

The next picture illustrates a non-screwed gunwale. Basically, the flare from the sides of the boat in the stern and amidships is translated to the gunwale to the bow, where there is minimal flare, the sides are relatively straight. Only muscling the gunwale with my hands could I make contact. Not conducive to gluing, as you can imagine.

Storer (el designero) promised that screwing the gunwale would pull it in. I had doubts and didnt want to deal with it, but I tried. Working from the stern forward, I placed one screw in the stern, two amidships, and two right in the bow area where the twist was most apparent. I used the 1 1/4 screws with the ply pads from the bottom screwing event.

SOB, it worked:


Nice and tight, all pulled together. This makes me happy. All ready for gluing. Screws were hidden underneath the areas where I am going to place my inwale spacers. Speaking of spacers, all of them are cut, and I have marked where I will be adding them. I started at the seam between the two pieces of ply for the sides, one will join them at the top, then one will be place next to each BH sidearm, with BH3 sidearms getting two small ones on either side due to the fact that it does not meet the side near the top. Re-enforcements, if you will. I need 52 spacers for this scheme.

Next up, I glued my daggerboard together.


I precoated the sides to be glued, then made a thin epoxy mix with the filler, not too much since the wood had been run through the joiner. The typical GIS clamp scheme as seen below:

And were off to the races! Looking good. Looking good.

She arrives, one step at a time boys, one step at a time.

Do you find information about Boat Plans Bolger are you looking for? If not, below may help you find more information about the Boat Plans Bolger. Thank you for visiting, have a great day.
Read More..

Plywood Boat Plans Australia | Symphony

Plywood Boat Plans Australia


This interesting and unusual yacht was lying on a mooring in Fowey recently.

The hull is constructed in clinker like planks, although that top plank is uncharacteristically wide and a bit of a odd shape.

The basic hull shape has quite fine ends and reminded me of a Van de Stadt designed Warshipp , were it not for the reverse sheer line. Not sure about the raised full width coach roof, but it would give good interior space in what is a small volume yacht.

With roller reefing on both jib and stay sail Symphony looks like she has done some serious offshore sailing. It would be nice to know more about her.


Do you find information about Plywood Boat Plans Australia are you looking for? If not, below may help you find more information about the Plywood Boat Plans Australia. Thank you for visiting, have a great day.
Read More..

Boat Plans And Kits | Passage to La Paz

Boat Plans And Kits


As usual, we enjoyed Mazatlan more than we expected to. Every time we visit this city we find new and interesting places to visit, and meet new and interesting people . This place is working its way up toward my top five favorite places to visit in Mexico. But all things come to an end, and our time in Mazatlan ended at 1100 on Monday, April 20th as Finisterra cleared the breakwater at El Cid, and headed northwest along the mainland coast.

The forecast was for light northwesterly winds so we motored in that direction, keeping about 10 miles off the coast, with the idea that we would be in a good position to make a quick passage across the Sea once the wind veered around to North. We wanted to pass to the north of Isla Cerralvo and avoid the Cerralvo Channel, which has earned a reputation in my mind as a frequently unpleasant stretch of water.

By dusk we were some 50 miles northwest of Mazatlan, still motoring over flat seas in 2-3 knots of wind. Later that night we bent our course further toward the west, expecting the wind to shift north and build to a forecasted 15 knots. That shift didnt happen and we continued across the Sea under power through a beautiful night with a sliver of waning moon hanging low over the western horizon.

We motored along all the next day over the same glassy seas. By late afternoon, Isla Cerralvo was off our port bow. About ten miles before we passed the rocks that lie off the northern tip of the island, a wind came up out of the south. It wasnt what I expected but I was glad to have it and quickly unrolled the jib, thinking that if it lasted more than ten minutes Id hoist the main and wed have a nice close reach across the north edge of the Cerralvo Channel. Instead the wind, a Coromuel, piped up to 25 knots and veered SW and then WSW, bringing a lumpy head sea with it and erasing my thoughts of a pleasant passage through the San Lorenzo channel.
The San Lorenzo Channel lies between Isla Espiritu Santo to the north and the Baja Peninsula to the south.

San Lorenzo is a fairly short and narrow channel with hazards to navigation on both sides, and it didnt take long to get through it in spite of the Coromuel wind and rough seas. I knew that once we passed through the channel the wind would back around to SW and continue all night. So as soon as we were well clear of the channel we turned and headed southeast to Puerto Balandra. The wind was still blowing 25-30 as we approached the bay in pitchy darkness. We could see the lights of a few boats anchored there, but as we approached closer we were able to pick our way between them and came to anchor at 2330 in the southwest corner of the bay, about 100 yards off some low bluffs that offered good protection from the waves, if not the wind.

With the big Rocna anchor and 120 feet of chain down in 20 feet of water, we had a quick dinner and a glass of wine. Then Lisa turned in and I sat for a while in the cockpit watching the stars twinkling in the moonless night. I kept an eye on the GPS as well, just to make sure the anchor was doing its job, then turned in myself around 0100.  I was up again at 0300 and 0600, monitoring the GPS but the anchor, as always, kept us in place.

The next two days were spent in lazy solitude in Puerto Balandra, the Coromuel wind blew both nights, giving way each day to lighter northerly winds and overcast skies. After two peaceful days we got the anchor up and headed into Marina Palmira in La Paz, where well stay a couple of weeks.




Do you find information about Boat Plans And Kits are you looking for? If not, below may help you find more information about the Boat Plans And Kits. Thank you for visiting, have a great day.
Read More..

Boat Plans Bruce Roberts | Bad back

Boat Plans Bruce Roberts


Well I went ahead and blew out my back again and now Im on some fun pain medications that make me feel quite fuzzy.

So I went ahead in my haze actually tied (marlin style lacing, scroll down here to see) my sail to the yard and boom as opposed to using plastic zip-ties, though those worked really well.  I optimized my downhaul a little better and most importantly, added a cleat on the boom to give me one level of outhaul purchase.  The outhaul runs from the clew to a loop at the end of the boom, then forward to a cleat.  Only one purchase, but already a marked improvement.  I re-tied the block tiedowns, re-sat the haylard block in the yard, jimmied things nice and straight and shes ready to rock now. 

Hopefully all this will take care of wrinkles, gaps, and inefficient sail shapes that have hindered speed and progress so far.  Time will tell.

Back, heal thyself!  Wind bring your forces to me!  Zinea, Pterodactylus, fly!

Do you find information about Boat Plans Bruce Roberts are you looking for? If not, below may help you find more information about the Boat Plans Bruce Roberts. Thank you for visiting, have a great day.
Read More..

Canoe Boat Plans



The 23ft Golif was built from 1962 by the Jouët works at Sartrouville. Jouët claim she was the first production small offshore cruiser to be entirely built in GRP, and she caused a stir on her introduction at the first Paris Boatshow in January 1962.

The unusual name comes from a famously ruthless, daring, and reportedly amorous 17th century French pirate, Louis Adhémar Timothée Le Golif, also known as “Borgnefesse”. Since his nickname means something like "one-eyed-arse", you would probably have been wise to address him, at least until you got to know him well, as Captain Golif.

Golif was designed by Jouet with one eye on the American market, where the management believed they could sell a lot of boats. They had probably been helped considerably in their objective by the earlier successful transatlantic voyages of Jean Lacombe, in a plywood Jouet Cap-Horn. Apparently the companys market research suggested that the Americans favoured rather more interior comfort than the European market was used to, and that stiffness under sail and transportability by road would be important qualities for US buyers. Some of the Golifs characteristic features, such as its panoramic cabin window, shoal draft, relatively light displacement and high ballast ratio, stem directly from these market-related requirements.

Even today, Golifs looks seem rather quirky, though the underwater hull shape and the rig appear conventional. At the time, however, Golifs rig was considered rather tall and narrow, and the aluminium mast was in those days quite an innovation on a small cruising yacht. The odd pinched shape of the coach roof seems to have been intended to maximise the width of the side decks, but without sacrificing headroom in the places below where you might want to stand. Thus, with perfect French logic, there is low headroom over bunks and seats, where you sit or lie down, but there is plenty of headroom over the central passage and galley area, where you stand or walk. As the Jouët company said, this deck was designed from the inside!

Unusually for such a small boat, Golif had a decent chart table at which you could comfortably sit and work while facing the direction of travel, as you might in a much larger yacht. This was achieved by making the chart table swing down from the cabin deckhead right in the centre of the boat. Another innovation was a hinged and sliding hatch (visible in the colour photo of a Golif recently for sale in France)

Some versions of the Golif were delivered with an optional deeper keel for racing performance. These boats were excellent performers in offshore races and won many prizes, but it was a perfectly standard Golif that achieved the greatest fame for the class. In 1964, Jean Lacombe who had been Frances sole entrant in the 1960 Observer Singlehanded Transatlantic Race (OSTAR), returned to repeat the feat in a Golif, once again the smallest boat in the competition. This was the year of Eric Tabarlys first triumph, so Lacombes achievement was rather overshadowed by the acclaim and fanfares garnered by the winner. Nevertheless, Lacombes Golif took joint pride of place, alongside Tabarlys Pen Duick II at the centre of the 1965 Paris Boat show. (see photo)

There are varying estimates of the total number of Golifs built by Jouet and also by the Dubigeon yard in Normandy. The total number certainly comes to over 1000.


Jouët Golif
LOA: 6.50m
LWL: 5.92m
Beam: 2.22m
Draft: 0.96m
Displacement: 1200Kg
Ballast: 480Kg (cast iron)
Sail area: 23.2sqm

Many thanks to the French Golif owners website for all the b&w images and much of the information used in preparing this post. Colour photo of a Golif recently for sale in France from an advertisement on www.leboncoin.fr

A scanned copy of the original 1963 Jouet Golif sales brochure is available in .pdf format from Yacht Brochures.co.uk



Do you find information about Canoe Boat Plans are you looking for? If not, below may help you find more information about the Canoe Boat Plans. Thank you for visiting, have a great day.
Read More..

Boat Plans Pdf | Barra de Navidad

Boat Plans Pdf


The Honcho sailed from Tenacatita on Thursday, February 3rd, bound for Barra de Navidad, about 14 miles down the coast. For this short hop we didnt hoist any sails. Instead we motored along the coast, looking in on a couple of coves where we might like to anchor in the future. As we approached the entrance to the lagoon at Barra, the wind piped up to about 20 knots and the sea grew lumpy and confused. The lagoon where we planned to anchor is up a narrow channel with shoals on both sides. Using waypoints taken from Shawn Breeding and Heather Bansmers "Pacific Mexico, A Cruisers Guidebook", I programmed the GPS with our route into the anchorage, and we got in around 1400 without mishap. We got the hook down in about 10 feet of murky water and sat back to enjoy the view while the wind whistled in the rigging.

The next day we joined some friends for a bus ride to Melaque, a seaside town on the northern side of Bahia de Navidad. Not a particularly picturesque place, Melaque does boast a bank and the excellent Hawaiian Market. We stocked up on food and beverages at the market, and pesos at the bank, then had lunch in a seaside restaurant before heading back to the boat.

A word on cruising guides. The Honcho left California with copies of "Charlies Charts" by Charles and Margo Wood, and "Mexico Boating Guide" by Pat Rains. In Puerto Vallarta we picked up a copy of the Pacific Mexico Guide. Charlies Charts, originally published in 1982 and periodically updated has been the most widely used guidebook for this area. The Rains guidebook was first published more recently and offers better maps and charts as well as some photographs. The Pacific Mexico book, published in 2010, is illustrated with accurate charts and maps using satellite photos and GPS technology. It is a significant improvement over the other guides in terms of providing accurate navigational information. Since acquiring this book, the others have, for the most part, stayed in the bookshelf. I highly recommend the Pacific Mexico Cruising Guide, as well as Shawn and Heathers other book, Sea of Cortez Cruising Guide.








Do you find information about Boat Plans Pdf are you looking for? If not, below may help you find more information about the Boat Plans Pdf. Thank you for visiting, have a great day.
Read More..

Boat Plans Catamaran | J 111 Review

Boat Plans Catamaran




Now that the Honcho is up for sale, were beginning to look for another boat and another adventure. Ive always liked J Boats, so I couldnt wait to see the new J/111, which we thought might be a fun high performance cruiser that would suit our needs. Well, after checking one out, we decided to keep looking because its not quite big enough for the voyages we are contemplating. But that doesnt mean its not a great boat. In fact, I think its one of the better boats J Boats has produced.
J/111 Outboard Profile

The J/111 is, in my opinion, a continuation of the J/35 theme...A fast, seaworthy boat that is offshore capable, but is most comfortable as a racer that a couple could easily spend a week at the island aboard. This is a type that J Boats excels at, so I though it would be fun to do a review of this design. A few years ago I spent some time cruising aboard a similar boat, an Aerodyne 38  called "Matador" and really enjoyed sailing across the southern reach of the Sea of Cortez from Cabo to Mazatlan aboard her. In 2003 we won our class in the Newport - Ensenada race in the same boat. Ill add some photos of both boats for your viewing pleasure, and Ill take this opportunity to credit Yachtworld.com for all of photos of both boats. I also encourage you to visit www.rodgermartindesign.com if youre interested in learning more about the A/38.


J/111


The J/111 reflects the state of the art in boats of this genre. With its plumb bow, long waterline, near vertical transom and bulb keel, the hull looks fast and its PHRF base rating of 42 looks about right to me. Interestingly, the Aerodyne 38 rates the same.

Aerodyne 38
Both boats have a deep bulb keel with a vertical leading edge and the all-important kelp cutter. This keel shape is one I have used in my own designs and it really is more efficient than, say, the keel on the Honcho.
J/111 Keel
The Aerodynes keel has a more torpedo-shaped bulb than this.

Both the J/111 and Aerodyne 38 have deep carbon fiber rudders and wheel steering. The wide sterns of these boats demand deep rudders to keep them from stalling when the boat is heeled at speed. Rudders on boats of this type are usually large relative to the keel as they not only steer the boat but help generate lift to weather as well.

I really like the aesthetics of both boats. The 111 looks more modern but that is to be expected. The cockpits are large and incorporate seating forward and wide open space aft. This is efficient for racing, but makes for a surprisingly friendly place to be if youre cruising, provided that the seats are long enough for an occasional snooze.
J/111 accommodations
Going below, the basic layout of the J/111 looks lightweight and efficient for racing. For cruising it would be snug. Notice that the head and V-berth are in the same cabin space. Id remove the cushions and relegate the V-berth to storage only. The quarterberths might be big enough for two and the settees in the main cabin would make reasonably good sea-berths if they were fitted with lee cloths. The galley is small, but probably adequate for short cruises and fixing simple meals for a racing crew. I like the nav station. Its big and has plenty of storage space.
J/111 interior
Light and open spaces abound


Aerodyne 38 main cabin
Engine is under the sinks

The Aerodyne, by contrast is oriented more for offshore racing or cruising. The layout incorporates a head aft to port and large quarterberth to starboard. The galley has plenty of counter space, with the Yanmar engine under the double sinks. The forward cabin is spacious and has a berth big enough for two.

The sailplans of both boats are similar. Big main, non-overlapping jibs, asymmetrical spinnakers on retractable poles, carbon fiber mast. Whats not to like here?
Aerodyne 38
High speed cruising

J/111 Under sail
Sweet!

I have not yet had an opportunity to sail the J/111 so I can only speculate on how the boat handles, but it is similar enough to some of my own designs and to the Aerodyne 38, which I have sailed, to expect that it will be very quick, with a light helm and fast acceleration out of tacks. The deep, high aspect ratio keel and fine bow combined with the lightweight and efficient sailplan will make it fast upwind. The high sail area/displacement ratio means it will be quick to heel in puffs and will require close attention to sail trim in windy conditions, but it will reward you with high speeds downwind. Overall, an exciting boat to sail. I can say the same for the Aerodyne, athough it will be a slightly more comfortable ride. My guess is that the J/111 will be slightly quicker in light air buoy racing and downwind racing. The Aerodyne would likely be a better choice for the longer downwind races like the Transpac.




Do you find information about Boat Plans Catamaran are you looking for? If not, below may help you find more information about the Boat Plans Catamaran. Thank you for visiting, have a great day.
Read More..

Boat Plans Wood | SUCCESSFUL DRY FIT!!!

Boat Plans Wood


SHE STANDS ON HER OWN!!! OH HAPPY DAY!




Shell slice you in two! AAAARRRRGGGHHHHHH!!!

Flash made BH1 and 2 darker than they are.




The last one here is through the transom hole.

A couple of notes:

Everything is almost perfectly level and/or lines up. Seat cleat on transom to BH4 for example, BH1 and BH2, transom and the sides etc.

I used 1 1/4" drywall screws with plywood backing on the heads.

My notches are all mostly too big, epoxy will have to fill them. Also, my bevel on the transom was a little too much, but it will be easy to plane down.

SHE LIVES! SHE LIVES! LONG LIVE MY BEAUTIFUL BOAT! POSEIDON BE PRAISED!

ZINEA FROM CRIMEA




Do you find information about Boat Plans Wood are you looking for? If not, below may help you find more information about the Boat Plans Wood. Thank you for visiting, have a great day.
Read More..

Boat Plans Aluminium Australia


Ive been working away in the shop, fitting the seat tops and filleting them, turning the offcuts into doublers under the edges and sanding out the odd dribbles of epoxy,  read on.

Blog 4 September

Its getting close,  today I fitted the forward seat top.   Tis is in two pieces joined down the middle and glued in to form  to form not only the seat but the top of the forward bouyancy tank, as well as bracing the mast box.


 Filleting, the white stuff is a low density filler from Epiglass with a little cotton mill fibre ( glue mix) mixed in, thats for strength. The brown is Microballoons but underneath that is a smaller fillet of straight glue applied about 6 hours before.  


So that’s done, yesterday I fitted the doublers under the edges of the center thwart and the after seat ( which should be referred to as “Stern sheets” but I’m not that “correct” in my terminology).  These doublers make a big difference to the feel of the boat, stiffening the overhanging edges of the seats considerably as well as giving them a much more “solid” appearance.
These adoublers re made from the scrap left over from cutting the big parts, there wont be much more than kindling left when I’m done with this project,  successively smaller parts get cut as the project goes on,  so the scraps get smaller each time around.


Stern sheets, the doublers sitting on the seat  above where they will be fitted underneath the overhanging plywood seat edge.


Center thwart.  This is a great way to use the offcuts from the planking, makes a much nicer job of the edges of the seat. Next job to do is to glue them in, then round them off.
Forward seat tops to come next.


So tomorrow its at them with the angle grinder and sander to finish off the endges, round them over and fair them.  Then some filleting, more sanding,  and then its time for paint.
I must say that the Fein Multimaster is an amazing tool for sanding fillets, the point of that triangular sanding head with 60 grit paper on it does a very good job, effortlessly and quickly.  I love this tool and would almost own it just for that.

Paint, the outside looks good,  two coats of primer, and two coats of  satin finish paint looks good, so tomorrow I’ll be splitting the white between two containers and pouring a little of the dark green into one to get the pale green for the interior and then start swinging that paintbrush again.

Tonight, my friend and next door neighbour Emily Scott sings.  She has won a scholarship to the UCLA School of Music where she will study in the Masters classical voice program,  this is seriously top level stuff!  I’ve been to a couple of performances and she’s got me converted to Opera.
Tonights performance is a fundraiser, she’s got to get enough money together to live in Los Angeles for two years to take up her scholarship, and I’m going along.

We’ve had shared dinners, helped each other out some, and enjoyed each others company.  I’ll miss her, all the very best Emily.

http://www.creative.auckland.ac.nz/en/about/news/news-2014/2014/07/scholarship-helps-talented-singer-find-her-voice.html

Here’s her facebook page, well worth a look.

https://www.facebook.com/profile.php?id=675895038&fref=ts

Time I got myself tidy, don’t need the black suit and tie but epoxy and paint covered overalls wont quite cut it.

( I went, full house, I listened, I enjoyed the concert immensely)







Do you find information about Boat Plans Aluminium Australia are you looking for? If not, below may help you find more information about the Boat Plans Aluminium Australia. Thank you for visiting, have a great day.
Read More..

Boat Plans Skiff | Bursledon Gig

Boat Plans Skiff


The Bursledon Gig is actually an adopted boat, built in fiber glass from a mould taken from a west country punt, the original boat probably dredging for oysters and doing other inshore work in Carrick Roads, Falmouth.



At 15’” LOA with a wide bean of 54", the Bursledon Gig is a stable rowing platform as was adopted by the Hamble Sea Scouts and others along the Hampshire River as a safe and versatile boat which can be rowed with up to four crew plus a cox.
With approaching 20 gigs on the river they became a regular fixture at Bursledon Regatta competing for the Sheave Trophy.



In 2010 Hamble River Rowing was formed to promote rowing on the river, the club now has two new gigs in build and another on order.



Do you find information about Boat Plans Skiff are you looking for? If not, below may help you find more information about the Boat Plans Skiff. Thank you for visiting, have a great day.
Read More..

Pontoon Boat Plans Aluminum | Scullmatix

Pontoon Boat Plans Aluminum


I purchased a scullmatix for my boats, and I gave it a whirl in the local pond.  My lovely wife took a picture of me sculling through the fog on IAZ,P.  It works... but I need more room to get it really going, me thinks.  Im primarily going to use it for the Sea Pearl 21.





Do you find information about Pontoon Boat Plans Aluminum are you looking for? If not, below may help you find more information about the Pontoon Boat Plans Aluminum. Thank you for visiting, have a great day.
Read More..